How to Install A Water Softener in Pre-Plumbed House?

So, you’re considering a water softener and already disregarded Magnetic Water Treatment.  Want to learn how to install water softener pre plumbed to a house that is already plumbed?

Hard water flowing through any pipe can contribute to inconvenience at best – and expense at worst. Hard water can corrode your pipes, dishwashing machines, and even damage your skin and hair (scalp and dandruff issues) if it’s used too often. Decide too if you want Water Softener pellets or crystals to use with your new system. Research this here to see which is the better option.

Hard water makes it difficult for detergents to bubble up, leaving residue on faucets, in tubs, and even on sinks. It can stain your fixtures and corrode your pipes, causing them to degrade and require replacement, meaning more financial pain. This is why many get water softeners installed, making them not a luxury anymore, but a necessity that helps protect your wallet.

Oftentimes water softeners can be installed via a licensed plumbing company. Even some hardware stores offer a one-stop-shop service that includes supply and installation. Speak to a plumber first to ensure you only have the proper water softener installed for your specific water usage and requirements. This saves time when it comes to how to install water softener pre plumbed and ready to go.

If you have chosen the Fleck 5600SXT 64,000 Grain Water Softener Digital SXT Metered Whole House System, then you can get in a contractor to fit this or do it yourself. The same applies to the Whirlpool WHESFC Pro Series range of products too.

Understanding Your Situation

Hard water is usually associated with minerals that can give the water an unpleasant taste and odor. Solving these problems, however, is a super easy task, as all you have to do is install a water softener in your home – a project that you could sometimes complete yourself in less than two-three hours. This helps you diced and learn how to install water softener pre plumbed to a house that is already plumbed without spending a lot of money.

Note: Be aware that not every house has the same plumbing needs; therefore, it is highly recommended to take the time to consult with a licensed plumber, as they have the experience and know-how of where to site it. You don’t need to hire them to complete the job either, but a little professional advice from the plumber before you start the project can be very helpful.

Installing a DIY water softener might sound complicated, but you should keep in mind that there are several different types of water softening systems for a pre-plumbed house to choose from, and each one comes with a different level of difficulty. If you are a novice handyman and want to know how to install a DIY water softener to a pre-plumbed house, be sure to follow the steps listed.

Factors to Consider Before Installing A Water Softener in Pre-Plumbed House

There are several factors like your house size, the type of pipes you have installed on your premises, and where you intend to install your water softening system. You obviously can embark on this project yourself, but if you don’t have any experience when it comes to home improvements, it is recommended to get professional assistance as they boast the skills and experience needed to complete the job efficiently.

Installing any water softening system on your property isn’t the easiest thing to do, but it doesn’t have to be terribly messy if you don’t know what you’re doing. It is a somewhat complicated task made even more confusing from the many plumbing vendors and their suggestions. This can cause a fair number of issues and usually creates negative sentiment, but you needn’t feel that way. Yes, we know that the Fleck will differ from the other brands, such as Whirlpool WHESFC Pro Series.

Related Articles: Top 5 Best Countertop Reverse Osmosis Water Filters

Like many home improvements projects that involve some tinkering with the plumbing, installing a water softener is typically not difficult, but can be tricky if you are uncomfortable with cutting through pipes, or do not follow instructions correctly. If that’s the case, it’s advisable you consider taking expert assistance, but if you have prior experience with DIY projects, embark on this project with full confidence, and I am pretty sure you will succeed without any problems and doubts.

Steps How To Install Water Softener Pre Plumbed

Be aware that every water softening system that you will buy will come with an owner’s manual. Whenever you install your water softener, you should refer to the included instructions to ensure that you are proceeding correctly, thus preventing you from making errors. An improperly installed water softener system will experience issues and, in due course, can ruin itself as well as damage to both the equipment and nearby fixtures in your home, resulting in unnecessary repairs and replacement of both the equipment and fixtures.

Also, before starting to install a water softening system, it is essential to check with your local city hall to ensure that you meet building standards. This includes whether or not you need to modify the configuration of your premises to comply with safety codes. For example, you may need to add a bypass valve or a shut-off valve to ensure that your premises are safe.

1. Shut off the water supply to your home in the mainline. By opening the lowest solenoid valve in your pipes, let the water flow into another tank that you want to flush. This will allow you to clear your pipes entirely before restoring the flow of water.
2. You will probably want to shut off a hot water heater and also switch off the electricity leading to it.
3. You need to determine the area along the main pipeline where the water softener is to be positioned. Remember that it must be attached to the heater or the hot water tank before the “tee” point. You need to get a drill bit and make some holes about 3 feet apart on the entire length of the pipeline. Flag the places along the sides where you will be drilling holes to help outline the borders of the softener area.
4. Use a pipe cutter to slice right through the mainline. Thread the pipe cutter right on the end of the pipe, and rotate in a clockwise manner until the flow of water is completely shut off.
5. It is important to install an assembly specifically designed for supply lines that include an elbow, which would make it easy for you to connect it to a check valve, which can allow you to feed water that goes directly to the refrigerator ice maker.
6. Make sure you measure the pipes that will lead to the bypass valve in order to make sure that it has the correct measurements. Once the pipes are cut off accordingly, make sure to solder on any pipes and fittings before you connect the pipes to the bypass valve.
7. The next thing you need to do is attach the connecting pipes to the rings of the water filter, which should come with the unit.
8. You will most likely have to make some modifications, including sealing around the holes and fastening the hose storage rack. If you are living in an area where extra precaution is taken, seal around any possible holes, and fasten your hose supply rack in a strategic location. Your hose should also be kept off the floor, as well as be secured to the wall or ceiling.
9. It is recommended to use a tube that is lead from the hub for the receiving side corresponding to the diameter of the receiving pipe which terminates above the level of the receiving line.
10. After turning the valve to the bypass position, it is good to flush out the condo lines with tap water in order to sanitize the pipes.
11. After setting up the filter to the backwash setting, it is ideal for you to open the valve very slowly so as to allow water to come into the system while releasing trapped air that would be found in the pipes. From now on, you can follow the instructions mentioned in the owner’s manual handling the flushing process, and even the addition of salt in the lines.

FAQs

We have put together a list of how to install water softener pre plumbed FAQs.

Q: How do I install a water softener pre-plumbed?
A: Installing a water softener that is pre-plumbed is relatively straightforward. Depending on the type of system you have, you may need to install brackets or other mounting hardware in order to secure the unit in place. Additionally, you should ensure that all tubing and fittings are properly tightened and connected, as well as secured with tape or clamps where necessary. Once the unit is installed and its connections are secure, your water softener will be ready for use!

Q: How often should I maintain my water softener?
A: Most water softeners require periodic maintenance, such as cleaning and replacing the resin filter. The frequency of maintenance may vary depending on the type of system you have and the amount of water your household uses. Generally, it’s best to check your system at least once a month and perform any necessary maintenance tasks.

Q: What are some common signs that my water softener isn’t working properly?
A: If your water softener is not working as it should be, you may notice an increase in scale buildup or an off-taste to your water supply. Additionally, reduced pressure or erratic operation can be signs that something is amiss with your unit. In these cases, it’s best to consult a professional for repair or replacement of your system.

Q: Are there any health risks associated with using a water softener?

A: No – there are no known health risks associated with using a water softener. In fact, many people find that their skin and hair feel softer when they use softened water due to its lack of minerals like calcium and magnesium that can leave residue behind otherwise. It’s always recommended to follow manufacturer guidelines when using a water softening system in order to ensure that you get the best results possible!

Verdict how to install water softener pre plumbed.

Since water softeners will surely produce worthwhile positive results for you, don’t wait for any more excuses to install one. Do your research and get in touch with your local plumbers in order to get more information, and enjoy your peaceful leak-free, clean and soft water!